$20.00
We will hold your cart for 15:00.
So you picked up a set of BDK PolyPro seat covers. Good call – they're one of the most popular ways to protect your seats without spending a fortune. But if you've ever wrestled with a seat cover that won't stay put, you know installation can be a bit of a puzzle. That's exactly why we put together this guide.
We'll walk you through every step, from prep to final adjustment. We'll also cover the common pitfalls – like headrest misalignment and loose fits – and answer the big questions: do they interfere with side airbags? How do you wash them? And what do you do if the back seat doesn't fit quite right?
By the time you're done, you'll have seat covers that look sharp and stay put, mile after mile.
Your BDK PolyPro full set includes covers for both front seats, a rear bench (or split bench, depending on your vehicle), and headrest covers for all positions. The exact count can vary, so check the included instruction sheet to see what matches your order.
Before you start, lay everything out and identify each piece. Front covers typically have a larger bottom section and a separate backrest cover. Headrest covers are usually smaller and may be shaped differently for front vs. rear.
First, move the front seats all the way forward and recline them slightly. This gives you easier access to the rear mounting points. Clean your seats if they're dusty or dirty – it's much easier to install covers on a clean surface, and it prevents grit from scratching your upholstery.
If your car has seat heaters, make sure they're turned off and cool to the touch before you start.
Slide the headrest cover over the top of your headrest. If your headrest is removable, it's often easier to take it off, slip the cover on, and then reinstall it. Smooth out any wrinkles so the cover sits flush. The elastic edge should hug the bottom of the headrest.
Slip the backrest cover over the top of the seat back. Align the seams with the contours of your seat – you'll usually find elastic straps at the bottom that hook under the seat base. Pull these straps tight and secure them to keep the cover from shifting.
For the bottom cushion, you'll likely have a separate cover. Place it over the cushion and tuck the edges into the crevice between the cushion and the seat frame. Use your screwdriver or trim tool to push the excess fabric into the gap for a clean look.
Some PolyPro sets have a one-piece design for the bottom – if so, just stretch it over and tuck as needed.
Rear seats are a bit trickier, especially with split benches. If you have a 60/40 split seat, you'll need to cover each section separately. Start with the backrests – slide the cover over each section and secure the straps underneath.
For the bottom cushion, you may need to lift it up. Most rear seats are held by clips or bolts at the front edge – consult your car's manual if you're not sure. Once the cushion is tilted forward, you can wrap the cover around it and tuck the edges firmly.
If your set includes a one-piece rear bench cover, you may need to unfold it and fit it over the entire bench. This is where patience matters – take your time to smooth out wrinkles.
Once everything is roughly in place, go back and tug every strap. PolyPro covers have elastic bands and hooks on the underside. Make sure they're centered and taut. A loose strap today means a bunched-up cover tomorrow.
For the front seats, double-check that the side airbag seam (if your vehicle has side airbags) is not covered. The PolyPro covers are designed to be airbag-compatible, but you must ensure the cover's side seam is aligned with your car's airbag deployment zone. If in doubt, check your car's manual.
Now sit in each seat and wiggle around. Do the covers shift? If they do, re-tighten the straps. Check that the headrest covers aren't crooked and the bottom covers haven't crept forward.
For a truly custom fit, you can trim the edges of the covers if they're too long – but do this only as a last resort. BDK PolyPro covers are designed to be universal, so a little extra fabric can be tucked away rather than cut. If you do trim, use sharp scissors and only remove small amounts, leaving at least an inch of hem.
It's tempting to leave the headrest in place, but removing it makes the cover fit much better and prevents loose cloth around the posts.
Skipping the elastic straps defeats the whole purpose. They're what keep the cover anchored. Take the extra minute to hook them properly.
If your rear seat is a split bench, don't try to force a one-piece cover over the gap. Use the separately provided pieces for each section.
If you have a BDK UltraSleek set, the process is similar but the materials are different – check out our UltraSleek guide for extra tips on faux leather.
One of the most common questions we get is whether PolyPro covers are safe with side airbags. The good news: BDK PolyPro covers are designed to be compatible with side airbags. They feature a special seam that is meant to tear open when the airbag deploys.
However, it's critical that you install them correctly. The seam must be aligned correctly with the airbag location. Usually, there's a label on the cover indicating where the airbag seam is. Do not block that area with extra fabric or tuck it in a way that could interfere with deployment.
If your car has side airbags in the seats, check your owner's manual to confirm the exact deployment path. If you have any doubts, consult a professional installer.
BDK PolyPro covers are universal, but that doesn't mean they fit every vehicle perfectly. They're best suited for standard bucket seats and bench seats. They work well in most cars, SUVs, and trucks, but may not be ideal for seats with integrated seat belts or heavy bolstering.
If you have a more exotic seat shape, you might need a vehicle-specific cover like the WeatherTech CupFone for your phone, but that's a different thing entirely.
For the rear, if you have a 60/40 split bench, make sure the set you ordered includes the correct number of pieces. The PolyPro full set does include split bench covers.
Keeping your PolyPro covers fresh is easy. Most stains can be wiped off with a damp cloth and mild soap. For deeper cleaning, you can remove the covers and machine wash them on a gentle cycle with cold water. Avoid harsh detergents and bleach.
After washing, air dry them – never put them in the dryer, as heat can shrink the material. Once they're dry, reinstall them following the steps above. For stubborn odors, sprinkle baking soda on the covers, let it sit for a few hours, then vacuum.
Remember, PolyPro is a type of fabric, so it's not completely waterproof. If you need waterproof protection, consider a different material like the Motor Trend AquaShield for your rear seats.
They are universal, but we recommend checking the dimensions against your seats. They fit most standard cars, trucks, and SUVs. If you have unusual seats, you may need to adjust or trim.
Yes, you can machine wash them on gentle with cold water. Air dry only.
PolyPro is not a highly insulating material, so seat heat should still pass through, though it may take a bit longer to notice. Always follow your car's instructions for seat heater use.
PolyPro is a woven polyester fabric that's breathable and durable. Other options like faux leather or UltraSleek offer a different look and feel. Check the product descriptions for details.
Installing BDK PolyPro seat covers is a straightforward afternoon project that pays off every time you get in your car. You'll protect your original upholstery from spills, pets, and wear, and you can even change up the look of your interior on a budget.
Follow the steps above, take your time, and don't skip the strap tightening. If you run into any issues, the BDK customer service team is helpful – but with this guide, you probably won't need them.
Ready to get started? Grab your set today and enjoy a fresh-looking interior.
